change time RENAULT TWINGO RS 2009 2.G Engine And Peripherals Passenger Compartment Connection Unit OBD Workshop Manual

87B-14
MR-413-X44-87B000$288.mif
V5
87B
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming
Use this command only with a new and blank UCH.
A new UCH is not coded and is therefore not assigned to the vehicle; once it is fitted on the vehicle, it must be
programmed to assign it to the vehicle.
To carry out this programming, always use a key belonging to the vehicle (allocated to the old UCH).
Thereare two programming methods: "Not connected" to the code server mode and "connected" to the code server
mode.
-In"not connected" mode, the CLIP diagnostic tool supplies a programming key and the user enters the im mobiliser
code.
-In"connected" mode, the CLIP diagnostic tool automatically exchanges the programming key and the immobiliser
code.
Before starting this operation, make sure that there are no components capable of interfering with the
electromagnetic field (e.g.: CB (Citizen Band), mobile phone, etc.).SC004
PROGRAMMING THE UCH
Equipment required
CLIP
Note:
After replacing just the UCH, no operation needs to be carried out on the injection and electric power-assisted
steering computers.
The computers keep the same immobiliser code.
IMPORTANT
When the UCH programming procedure is successfully completed, the UCH is no longer blank and is
permanently assigned to the vehicle. It will not work on another vehicle.
IMPORTANT
When the programming operation is complete, only remove the key once theProgrammingcompletemessage is
displayed on the screen. Otherwise, programming has failed and the UCH cannot be used.
IMPORTANT
In "not connected" mode, once the tool has issued the programming key, the user has a limited amount of time in
which to enter the immobiliser code.
If this time expires, the CLIP diagnostic tool displays the message "Time expired. Restart the procedure''.
IMPORTANT
In "connected" mode, the exchange of the programming key and the entry of the immobiliser code is done
automatically. If the connection parameters are not met, "connected" mode switches automatically to "not
connected" mode.
MR-413-X44-87B000$288.mif
UCH
Vdiag No.: 44

87B-16
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
This key allocation operation enables you to assign keys to the vehicle.
To add one or more keys, replace one or more keys, de-allocate one or more keys (in the event of theft for example).
There are two programming methods: "Not connected" to the code server mode and "connected" to the code server
mode.
-In "not connected" mode, the CLIP diagnostic tool supplies a programming key and the user enters the
immobiliser code.
-In "connected" mode, the CLIP diagnostic tool automatically exchanges the programming key and the immobiliser
code.
Before starting this operation, make sure that there are no components capable of interfering with the
electromagnetic field (e.g.: CB (Citizen Band), mobile phone, etc.).
Only a non blank UCH can be programmed with keys.
With this system it is not possible to replace some components, such as the UCH and the key as these parts are sold
blank and uncoded.SC015
KEY ALLOCATION
Equipment required
CLIP
IMPORTANT
It is not possible to allocate more than two blank keys per operation.
If more than two keys must be allocated: program 2 blank keys then repeat the procedure with all the keys.
WARNING
If not all of the keys are available, all the keys will have to be reallocated later. Keys not inserted will no longer be
allocated to this vehicle.
WARNING
Only cards which have been ordered for the vehicle concerned or the vehicle's old cards can be inserted.
IMPORTANT
When the programming operation is complete, only remove the key once the Remove the key message is
displayed on the screen. Otherwise the programming operation has failed and the key will be unusable.
WARNING
When the tool issues the programming key, the user has a limited time in which to enter the immobiliser code.
If the time has elapsed, the Clip tool displays the message: Time elapsed.Restart the procedure.

87B-17
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
Key allocation procedure
–Establish dialogue with the UCH
–Select the Repair mode menu
–Select the Secure programming menu
–Select line SC015 Allocate key.
The procedure for allocating keys is divided in two parts:
1Key insertion stage.
2Key allocation stage.
1 - Key insertion stage
Clip requests that the keys to be allocated are inserted.
Insert ALL the keys to be allocated (old and new blank keys); any keys not inserted at this stage will be rejected in
the Key allocation stage and the operation will have to be restarted from the beginning.
Once all the keys are inserted, the Clip diagnostic tool displays the programming key.
To obtain the immobiliser code, see Technical Note 5037A, Code delivery procedure.
2 - Key allocation stage:
Continue the procedure following the instructions on the CLIP diagnostic tool.
Once the keys have been allocated, make sure that all the keys can lock and start the vehicle.SC015
CONTINUED
IMPORTANT
In "not connected" mode, once the tool has issued the programming key, the user has a limited amount of time in
which to enter the immobiliser code.
If this time expires, the CLIP diagnostic tool displays the message "Time expired. Restart the procedure''.
IMPORTANT
In "connected" mode, the exchange of the programming key and the entry of the immobiliser code is done
automatically.
If the connection parameters are not met, "connected" mode switches automatically to "not connected" mode.
IMPORTANT
The programming key can only be used for a limited time, as shown by the Clip diagnostic tool. After this time,
the programming key and associated immobiliser code are no longer valid. The operation must be restarted from
the beginning.

87B-19
MR-413-X44-87B000$288.mif
V5
UCH
Vdiag No.: 44PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Configurations and programming87B
Injection immobiliser code programming procedure:
–Establish dialogue with the UCH
–Select the Repair mode menu
–Select the Secure programming menu
–Select line SC017 Program injection immobiliser code.
Follow the instructions on the CLIP diagnostic tool.
When the CLIP diagnostic tool displays the programming key, make a note of this key and the VIN code.
To obtain the immobiliser code, see Technical Note 5037A, Code delivery procedure. SC017
CONTINUED
IMPORTANT
The programming key can only be used for a limited time, as shown by the Clip diagnostic tool. After this time,
the programming key and associated immobiliser code are no longer valid. The operation must be restarted from
the beginning.
IMPORTANT
In "not connected" mode, once the tool has issued the programming key, the user has a limited amount of time in
which to enter the immobiliser code.
If this time expires, the CLIP diagnostic tool displays the message "Time expired. Restart the procedure''.
IMPORTANT
In "connected" mode, the exchange of the programming key and the entry of the immobiliser code is done
automatically.
If the connection parameters are not met, "connected" mode switches automatically to "not connected" mode.

87B -128
MR-413-X44-87B000$624.mif
V5
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
UCH
Vdiag No.: 44
87B
ET114
ET115
WIPER REQUEST BY RAIN SENSOR
LIGHT ACTIVATION REQUEST BY LIGHT SENSOR
NOTESThere must be no present or stored faults.
Make sure that the vehicle is fitted with the rain and light sensor.
The status should change to LOW SPEED or HIGH SPEED if there is water on the
windscreen where the sensor is positioned.
The status should change to PRESENT when the light intensity requires the lights to
be switched on with the engine running.
Make sure that the other positions of the wiper control are working properly
Check the following configurations:
–Check that LC008 Daytime running lights is "With". Otherwise run CF014
Daytime running lights.
–Check that LC044 Rain/light sensor displays "Present". If not, run CF035 Rain/
light sensor.
–Check that LC095 Automatic headlight function displays "With". If not, run
CF193 Automatic headlight function.
–Check that LC096 Automatic wiper function displays With. If not, run CF194
Automatic wiper function.
SPECIFICATIONSET114: ABSENT/LOW SPEED/HIGH SPEED
ET115: PRESENT/ABSENT
Conditions:
Check that the switch stalk (component code 209) is in the intermittent position so that automatic operation can
be activated.
Check that the vehicle has a rain/light sensor (component code 1415).
Check that the function is not deactivated, perform the following cycle twice to activate the automatic headlight
function: Switch stalk (component code 209) OFF → Σωιτχη σταλκ (χοµπονεντ χοδε 209) to side lights ON
position.
Check the condition and connection of the 3-track connector of the rain/light sensor (component 1415) (tabs
bent, broken or oxidised).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check for + 12 V on connection BPT of component 1415.
Check for earth on connection MAM of component 1415.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRRepeat the conformity check from the start.
Carry out fault finding on the system.
UCH_V44_ET114 / UCH_V44_ET115